Product Finder

Compact front loader for dual flush-to-kerb milling

  • The cold milling machine with a working width of 6 ft. 11 in. (2.10 m) features a zero side on the right and left hand side to enable dual flush-to-kerb milling.
  • The milling unit can be hydraulically shifted to either side by 15.7 in. (400 mm), enabling maximum flexibility in its use.
  • The machine is ideal for major construction sites where trucks have to cut into flowing traffic to remove the milled material.
  • The large milling machine is especially suitable for milling on demanding and narrow construction sites in urban environments.
  • Three adjustable milling drum rotation speeds allow for high milling output rates under changing demands.

Technical Highlights

Find out about the components of WIRTGEN large milling machines

  1. Traction drive

    • Hydraulic pre-tensioning of track chains
      Hydraulically pre-tensioned track chains for optimized operation.
    • Traction control
      Intelligent electronic traction control system for the track units.
    • Track speed adjustment
      Electronic adjustment of the track speed during cornering to ensure maximum traction and low wear and tear.
    • Four-fold full-floating axle
      Four-fold full-floating axle for optimum machine stability.

    Additional Information

  2. Milling drum unit

    • Side-moving milling drum unit
      Milling drum unit movable by 16" each to the left and right hydraulically to allow dual flush-to-curb milling.
      FCS Light for the quick replacement of milling drums in FB2000 and FB2200 milling drum units.
    • HT22 quick-change toolholder system
      Extra efficient, tried-and-tested HT22 quick-change toolholder system as standard equipment.
    • Right-hand side plate lift of 18"
      Right-hand side plate can be raised by up to 450 mm to allow flush-to-kerb milling at the full milling depth.
    • Load-controlled water spray system
      Water spray system with automatic adjustment to the milling performance for optimum tool cooling.
    • Milling drum turning device
      Drum turning device to enable cutting tool replacement with the diesel engine switched off.

    Additional Information

  3. Levelling

    • Large choice of sensors
      LEVEL PRO automatic levelling system as standard equipment, offering a large choice of sensors and highly precise control of the milling depth.
    • Milling depth indicator
      Milling depth indicator on the LEVEL PRO screen (showing difference between scraper blade and side plate positions).
    • Scanning in front of the milling drum
      Scanning in front of the milling drum via hydraulic cylinders with integrated measuring system – suitable for use also with the Multiplex system.
    • Automatic system to initiate the milling process
      Automatic system to initiate the milling process with load-controlled lowering speed.

    Additional Information

  4. Engine station

    • Three different milling drum speed options
      Three selectable cutting speeds for optimum millingperformance in a broad range of applications.
    • Load-controlled fan speed
      Fan speed governed by engine temperature for low energy consumption and low noise emission levels.

    Additional Information

  5. Conveyor system

    • Large slewing angles
      Conveyor slewing angles of 60° to both sides to optimize the loading process.
    • Tremendous conveying capacity
      High conveyor loading capacity and drive power for highly effcient material loading.
    • Vacuum Cutting System
      Vacuum Cutting System for improved visibility.
    • Folding conveyor with locking mechanism
      Folding conveyor with intelligent mechanical locking mechanism for easy transport.

    Additional Information

  6. Electrical system

    • Emergency operation
      Electrohydraulic power pack to raise machine in emergency mode.
    • Camera system
      Robust camera system including up to six cameras and up to two screens.
    • Job data
      Precise recording of job data including “truck full” message.

    Additional Information

  7. Operator's platform

    • Multifunctional joystick
      Multifunctional joystick with driving, steering, selecting operating mode, raising machine and switching off conveyor functions.
    • Ergonomics
      Ergonomically designed, backlit controls for non-tiring, productive working.
    • Protective canopy
      Fixed protective canopy with telescoping side panels for maximum protection from inclement weather.
    • Parallel alignment of machine
      Automatic parallel alignment of the machine both during the milling operation and in transport mode.

    Additional Information

  8. Machine frame

    • Perfect visibility
      Slender machine frame design at the front including dual wasp waist for a perfect view of the milling edge.
    • Ease of transport
      Ease of transport due to low machine weight and variable additional weights of up to 3,740 lbs.

    Additional Information

Technical specifications

Detailed information about the W 200 Hi

Model W 200 Hi
Milling width 2,100 mm6′ 11″
Milling depth 0 mm - 300 mm0 - 12″
Engine power 455 kW / 619 PS455 kW / 610 HP
Emission standards EU Stage IV / US EPA Tier 4fEU Stage IV / US EPA Tier 4f
Operating weight CE * 30,400 kg67,021 lbs
W 200 Hi i Milling width 2,100 mm6′ 11″ Milling depth 0 mm - 300 mm0 - 12″ Engine power 455 kW / 619 PS455 kW / 610 HP Emission standards EU Stage IV / US EPA Tier 4fEU Stage IV / US EPA Tier 4f Operating weight CE * 30,400 kg67,021 lbs
  1. [*] Weight of machine with half-full water tank, half-full fuel tank, driver (150 lbs/75 kg) and tools.

Large milling machine W 200 Hi (Brochure)

Illustrations and texts are non-binding and may include customized fittings. Subject to technical changes. Performance data depend on operational conditions.

Market-leading and cutting-edge products for the Road and Mineral Technologies business sectors are constructed at the WIRTGEN brand headquarters in Windhagen, Rhineland-Palatinate. With its innovative, high-performance and cost-efficient products and technologies for cold milling, soil stabilization, hot and cold recycling, concrete paving and surface mining, WIRTGEN leads the world market in road construction and repair, as well as in mining natural rock and pay minerals.

© 2019 WIRTGEN GmbH